products category
YY/T0583.2-2016 一次性使用胸腔引流裝置綜合測試儀TDE-01檢測儀器(通用名稱為胸腔引流測試儀)依照“YY/T 0583.2-2016 一次性使用胸腔引流裝置 第2部分:干封閥式"標準中規定設計制造,適用于測試干封閥式一次性使用胸腔引流裝置的負壓狀態顯示器的試驗、開啟壓力、關閉性能、高負壓自動釋放閥性能的檢測。
胸腔引流裝置綜合性檢測儀
YY/T0583.2-2016 一次性使用胸腔引流裝置綜合測試儀主要參數
產品名稱:胸腔引流測試儀
測試范圍:-100~10 KPa(標配)
精度:0.5%FS
氣源壓力:≤ 0.7 MPa(氣源用戶自備)
氣源接口:Φ6 mm聚氨酯管
外形尺寸:390 mm (L) × 410 mm (W) × 190 mm(H)
干封閥式一次性使用胸腔引流裝置負壓狀態顯示器試驗方法:引流裝置處于供使用狀態。安裝試驗裝置。手動操作吸引源(血壓計的氣球適宜),在引流接口處緩慢施加負壓至6 cmH?O,觀察負壓顯示器是否能清晰地顯示負壓狀態。釋放負壓,觀察負壓顯示器是否能清晰地顯示非負壓狀態。再重復該試驗兩次。
干封閥式一次性使用胸腔引流裝置開啟壓力試驗方法:
使引流裝置處于供使用狀態,但氣體泄漏計中不加入水。安裝試驗裝置。手動操作加壓源(血壓計的氣球或注射器),在引流接口處緩慢施加正壓,檢驗干封閥的開啟壓力是否小于2cmH?O.
干封閥式一次性使用胸腔引流裝置關閉性能試驗方法:
使引流裝置處于供使用狀態,但氣體泄漏計中不加入水。如圖B.2安裝試驗裝置,用手指堵住三通的上孔,手動操作吸引源,使積液腔負壓值達到-2 cmH?O.,手指釋放三通的上孔,使吸引口與大氣接通,觀察并記錄1 min內積液腔的負壓的變化。
分別在-5 cmH?O.、-10 cmH?O.、-20 cmH?O.、-30 cmH?O.、-40 cmH?O.和高負壓自動釋放閥釋放壓(如果有)的試驗壓下重復以上步驟。
注:若制造商聲稱的正常使用的最高負壓值低于-40 cmH?O.,則選擇正常使用的最高負壓值前的各試驗壓,—10 cmH?O.以后的各試驗壓依次以 10 cmH?O.遞增。
干封閥式一次性使用胸腔引流裝置釋放壓試驗方法:
1 連接試驗系統。堵住除高負壓自動釋放閥以外的所有進出口(必要時對封堵質量進行檢驗)
2 用引源對試驗系統緩慢施加負壓,記錄高負壓開始釋放的瞬間水壓差計讀數,即為高負壓自動釋放閥釋放時的釋放壓。
3 重復三次 2過程。
4 以高負壓自動釋放閥三次釋放的平均釋放壓報告結果,并以厘米水柱表示。
濟南眾測機電設備有限公司
86-0531-88983898
濟南市高新東區孫村街道大正路銀豐國際生物城園區A3-02
3325919032@qq.com
掃碼關注我們
Copyright © 2024濟南眾測機電設備有限公司 All Rights Reserved 備案號:
技術支持:制藥網 管理登錄 sitemap.xml